We've encountered this post involving How to Install a Bathtub Yourself listed below on the net and reckoned it made good sense to talk about it with you over here.
Mounting a bath tub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably difficult task. If the old tub is easily accessible, the project can relocate easily; if you have to open a wall to eliminate the old bathtub as well as position the brand-new bathtub, the job is a lot harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub and also set in the brand-new one. Make sure you have qualified yourself for the work and also fit trying it. Instead of employing a contractor to take control of a halfway-completed job, it is better to think about employing one before you start. Possibilities are you might need a professional plumber to make tube links.
This short article will assist you mount a brand-new tub in your washroom if you have already bought a brand-new bathtub and also don't need to change the arrangement of your previous water pipes.
Your devices and also material checklist ought to make up the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water system. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be rather troublesome due to the restricted accessibility that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly originate from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Prior to going on to fit the new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in place between the tap and the sink. Secure the tap in place with the maker provided backnut. Once the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The previous type should be attached to the tap ends initially, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the needed setting. The wood boards are useful in evenly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the outermost flexible tap connector to the appropriate supply pipe by making a compression join; then do the exact same for the other faucet.
Switch on the water and also inspect all joints as well as new pipework for leakages and also tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the bath tub ought to wait until the bath tub has been made use of a minimum of when as this will resolve it into its last position.
Planning for the Installation
To start with, the sustaining frame provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to stop strain on the tub.
Fit the versatile tap ports to the bottom of both taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be suited its last position.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the tub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealant can fracture fairly very early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that article about How to Install a Bathtub Yourself from a friend on another website. Loved our blog? Please share it. Help another person locate it. Kudos for your time. Visit us again soon.
Visit Homepage